Search:

Type: Posts; User: The Guz

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 40 minute(s) ago.

  1. Replies
    2
    Views
    320

    Reload is not recommended on SiC during the...

    Reload is not recommended on SiC during the application phase. It is fine for maintenance.
  2. Replies
    2
    Views
    6,655

    I have not used Sonax in a very long time. I...

    I have not used Sonax in a very long time. I purchased a gallon of Clarify for like $30 from Autopia a long time ago so still using that gallon up.
  3. Replies
    2
    Views
    928

    It looks like there is some left over 3M...

    It looks like there is some left over 3M adhesive. Was glue also used?
  4. Replies
    2
    Views
    1,466

    You can check it out on my channel ...

    You can check it out on my channel


    https://www.youtube.com/watch?v=MZaNS3jTiDI&ab_channel=MikeG
  5. You will need to polish to remove it.

    You will need to polish to remove it.
  6. Replies
    6
    Views
    1,483

    It does not need a topper if it is going to sit...

    It does not need a topper if it is going to sit in the garage. Wait until the first wash and you can use any of those products.
  7. Replies
    1
    Views
    2,356

    You can do what is referred to as a 3 pH wash to...

    You can do what is referred to as a 3 pH wash to perform a decontamination wash. This will remove any toppers on the coating.

    Pre-Foam with Lift
    Rinse
    Pre-Foam with Descale
    Contact Wash with...
  8. Replies
    3
    Views
    2,618

    I have not used Perl on leather. I have used CQ...

    I have not used Perl on leather. I have used CQ Leather 2.0 and it feels like the leather is unchanged. If your leather needs moisture I would stick with something like colourlock.
  9. Replies
    3
    Views
    2,618

    You want one or the other but not both. The...

    You want one or the other but not both. The coating needs to bond to the surface. Perl won't allow that to happen.
  10. Replies
    3
    Views
    15,647

    Thanks. You are correct. Avi in the posted...

    Thanks. You are correct. Avi in the posted snapshots mentioned that as well.
  11. Replies
    6
    Views
    1,483

    Give it a good wash with reset, eraser wipe down...

    Give it a good wash with reset, eraser wipe down and then add the second layer.
  12. Replies
    6
    Views
    2,159

    The water through the foam cannon will dilute it...

    The water through the foam cannon will dilute it even more. Try out the dilutions and play around with that.
  13. Replies
    6
    Views
    2,159

    CarPro MultiX would be an option.

    CarPro MultiX would be an option.
  14. You would be fine with either one. They both...

    You would be fine with either one. They both work fine on a nav screen.
  15. I coat the trim once a year to keep it looking...

    I coat the trim once a year to keep it looking good. It will turn white over time and look splotchy. You can use reload.

    Clean the trim, panel wipe and apply a fresh layer yearly.

    Also...
  16. That’s your source of the dust. Stop using it...

    That’s your source of the dust. Stop using it and you should notice little to no dust accumulation.
  17. What car duster is it?

    What car duster is it?
  18. Replies
    1
    Views
    4,125

    PPF can be polished. Something like Reflect or...

    PPF can be polished. Something like Reflect or Essence will work just fine.
  19. Replies
    3
    Views
    1,537

    That is a high spot. Spot correcting will leave...

    That is a high spot. Spot correcting will leave that one section darker. It would be best to polish the entire panel and re-coat.
  20. Replies
    5
    Views
    5,750

    Test spot with a polishing pad and see how it...

    Test spot with a polishing pad and see how it does before coating it. If that does not remove it you may need to step up to a more aggressive polish with a polishing pad.
  21. Reset will neutralize the acidic nature of...

    Reset will neutralize the acidic nature of Descale. You are essentially doing a 3 pH wash.
  22. This is what I would recommend. Process for...

    This is what I would recommend.

    Process for using
    1)Foam Lift Presoak
    2)Pressure wash Lift and as much dirt and other "stuff" off
    3)Foam Descale and leave on the surface
    4)Wash with Reset...
  23. Replies
    5
    Views
    2,651

    Review - CarPro DarkSide

    First up to review from the new CarPro products is CarPro DarkSide.

    I was sent this product to test out by CarPro.

    DarkSide is the newest tire product offering from CarPro. This is a...
  24. Replies
    4
    Views
    4,855

    You won't find carpro products locally which this...

    You won't find carpro products locally which this forum focuses on.
  25. Replies
    5
    Views
    3,792

    What was the prep prior to applying the coating...

    What was the prep prior to applying the coating on the glass? A coating definitely prefers a polished surface. You will need to polish the glass to remove the coating and start over as you are...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4