Spotless not removing spots ?

[krazygraphics]

I've been trying for 2 days to get some water spots off the hood of my Infinity G37 , I've followed the directions as posted on the link I ordered it from. I used a sponge to work it in , then I let it soak in for 2/3 min and that didn't remove them. I also saw a video that this would work good on glass ... this was a HUGE failure on my end.

Anyway I don't care much about the glass , I will deal with that another day . As far as the water spots on the car , none are being removed. Any advice ?


P.S pic of jeep windshield after Spotless

 

[ChrisDA]

You have to be VERY careful with Spotless on glass. I certainly doesn't suggest that you use it on Glass, on the packaging. I never let spotless sit for any longer than the work in time with a sponge/applicator.

It's very important to rinse with LOTS of water afterwards. Spotless is awesome at removing water spots, however there are just some water spots that have been there for too long and are embedded in the surface, which will need polishing out.

You'll need to polish that glass now.

 

[Corey]

Spotless is your best bet to chemically remove mineral deposits however once those spots are etched into the paint you must polish. You see, you can't remove an etching. An etching is a "void" - In other words the paint is thinner there- it has been "etched" So removing minerals doesn't add paint back to the spot once it is etched. In this case you must polish to level the are around it to no longer visualize a "void". I hope that makes sense to you.

As for the glass you should NEVER spray a strong acidic solution all over the glass like that. On glass especially its important to work ONE section (spray product directly onto mf and rub in and off immediately. You should not spray or let sit on glass and you should buff off completely and neutralize with waterless spray or water.

Finally, you will find when using professional grade products it is intelligent to learn how to use in one area BEFORE you place it all over your windshield and leave it there without removing.

Its also a good idea to understand you should not use chemicals in the sun as this can change the chemical makeup during use.

I hope that helps.

 

[Moldavite]

thanks for the info

 

[shagnat]

Spotless is your best bet to chemically remove mineral deposits however once those spots are etched into the paint you must polish. You see, you can't remove an etching. An etching is a "void" - In other words the paint is thinner there- it has been "etched" So removing minerals doesn't add paint back to the spot once it is etched. In this case you must polish to level the are around it to no longer visualize a "void". I hope that makes sense to you.

As for the glass you should NEVER spray a strong acidic solution all over the glass like that. On glass especially its important to work ONE section (spray product directly onto mf and rub in and off immediately. You should not spray or let sit on glass and you should buff off completely and neutralize with waterless spray or water.

Finally, you will find when using professional grade products it is intelligent to learn how to use in one area BEFORE you place it all over your windshield and leave it there without removing.

Its also a good idea to understand you should not use chemicals in the sun as this can change the chemical makeup during use.

I hope that helps.

Old thread revived..... Corey, does the sun change the chemical makeup or is the heat from the sun. With temps now being 40*F at night and 65-70*F daytime... would it be ok if used in the sun? Or is that ALWAYS at no no?

 

[DARK HORSE]

Old thread revived..... Corey, does the sun change the chemical makeup or is the heat from the sun. With temps now being 40*F at night and 65-70*F daytime... would it be ok if used in the sun? Or is that ALWAYS at no no?

I would NOT use Spotless in the sun!

Spotless is a very strong mineral deposit remover. I would be cautious and follow the suggested directions which include: First washing and drying the vehicle to remove any surface grime or contaminants that could interfere with the performance of Spotless. Ensure that the vehicle is parked in the shade, and that the surface to be treated is cool to the touch. Start by shaking the bottle to integrate the active ingredients before use. Either spray Spotless onto a microfiber towel, sponge, or CarPro applicator/suede and work the solution over the surface, one panel at a time. Wipe off with MF, and remove residue by thoroughly rinsing with water. Or spray directly onto the surface, and work the product in thoroughly one panel at a time with microfiber towel, sponge, or CarPro applicator/suede. Immediately wipe off the remaining product residue with a soft Microfiber Towel, and rinse the surface thoroughly to neutralize the solution.